LED Power Supply

Desktop LED Power Adapter 120W (12V/24V)

Desktop AC/DC adapter for samples, displays and small installations: 100–240 VAC universal input, 12 V 8 A or 24 V 5 A output (120 W), C8 inlet and 5.5 × 2.5 mm DC plug. Fully certified for the EU market — TUV, CE, GS, UKCA.

  • Universal 100–240 VAC input
  • 12V 8 A / 24V 5 A, 120 W
  • TUV, CE, GS, UKCA certified
  • C8 socket + 5.5×2.5 mm DC plug
  • Full protection set, DOE VI efficiency

Typical values shown. Custom density, CCT, CRI, IP rating, connector and packing on request — see Custom / OEM / ODM.

Technical specification

Constant-voltage 12V / 24V LED power supplies: IP67 waterproof drivers for outdoor runs, indoor metal-case SMPS for cabinets and coves, slim drivers for light boxes and desktop adapters for samples and displays.

Every figure below is a typical value for the standard build. Density, board width, CCT, CRI, IP rating, cut pitch, connector and packing are all made to order — send us the numbers you need and we confirm them in writing with the sample.

Power120W max
VoltageDC12V / DC24V
IP ratingIP20
OutputConstant voltage, DC12 V (8 A) or DC24 V (5 A)
Rated power120 W
Input voltageAC100–240 V, 50/60 Hz, 1.5 A max
EfficiencyDOE VI / CoC level, ≥ 88 % typical
Ripple & noise≤ 200 mVp-p
ProtectionOver-voltage, over-current, short circuit, over-temperature
AC inletC8 (figure-8), interchangeable cords EU / US / UK
DC plug5.5 × 2.5 mm × 10 mm, straight (right-angle on request), 1.2 m lead
Dimensions149 × 66 × 30 mm
Working temperature-20 °C to +40 °C
CertificationTUV, CE, GS, UKCA, SAA, KC, FCC, PSE
Warranty3 years
Installation & use

How to install Desktop LED Power Adapter 120W (12V/24V)

Plug-and-play for samples and display kits — no wiring needed.

Step by step

  1. Match the adapter voltage to the strip: a 24 V strip must never be connected to a 12 V adapter and vice versa.
  2. Connect the DC plug to the strip's barrel jack or DC terminal block; observe centre-positive polarity.
  3. Plug the C8 cord into the adapter and the wall outlet; the adapter idles at < 0.3 W when the strip is off.
  4. For continuous runs, load the adapter to no more than 80 % (about 96 W on the 120 W model).

Before you power up

  • Desktop adapters are IP20 — for bathrooms, outdoor or damp zones use the IP67 driver instead.
  • The adapter may click into hiccup mode if shorted; remove the fault and unplug/replug to recover.
  • For permanent installations, replace with a wired driver — adapters are meant for pluggable loads.

Typical applications

  • Sample kits and showroom displays
  • Trade-show and photo props
  • Small cabinet and desk lighting
  • E-commerce strip kits
Same family

Other LED Power Supply options

IP67 Waterproof LED Driver 60W–200W

IP67 Waterproof LED Driver 60W–200W

Fully potted aluminium constant-voltage driver for outdoor and damp locations. 170–264 VAC input, DC12V or DC24V output from 60 W to 200 W, with short-circuit, overload, over-voltage and over-temperature protection — the standard driver for outdoor coves, facades and signage.

60W / 100W / 150W / 200W · DC12V / DC24V · IP67

Indoor Switching Power Supply 250W (12V/24V)

Indoor Switching Power Supply 250W (12V/24V)

Metal-case constant-voltage SMPS for indoor LED strip installations: 250 W, DC12V 20 A or DC24V 10 A, with perforated housing for free-air cooling and screw terminals for clean, serviceable wiring. The workhorse driver for coves, cabinets and display runs.

250W (20A at 12V / 10A at 24V) · DC12V / DC24V · IP20

Slim IP67 Waterproof LED Driver 100W

Slim IP67 Waterproof LED Driver 100W

Ultra-slim 25 mm potted driver built for narrow spaces: light boxes, channel letters, blind coves and curtain pockets. 100 W at DC12V 8.3 A or DC24V 4.2 A, fully sealed to IP67 despite the flat profile.

100W · DC12V / DC24V · IP67

Get the datasheet and a price for this strip

Send quantity, target CCT and delivery market. We answer with spec and price, usually in one working day.

WhatsApp Request Quote